LANmark-OF ENSPACE Method C Pre-Term OM5 x24F MTP/M-MTP/M Low Loss fan out E xxxm LSZH B2ca Lime Green
- Factory terminated MTP-MTP fibre assembly
- Flexible fan-out for ease of installation in patch panel
- Small cable diameter reduces required data centre space
- Method C polarity Pre-Term
- Only one type of patch cords and one type of cassettes required for duplex transmission
- Fibre count: 24F
- Fibre type: OM5 Wideband
NormesInternationales : ISO/IEC 11801
Pre-Term for data centres, buildings and campus based on Micro-Bundle Universal
The cable has a small diameter and bend raduis to meet data centre requirements.
The cable is watertight and rodent retardant due to the glass yarns. It can be used in buldings and between buildings.
The cables have been tested for fire performance according to the new Construction Product Regulation: EN50575:2014 +A1:2016.
According to this standard the cables have a very high fire performance with minimal fire load and spread, smoke density, droplets and acidity: B2cas1,d0,a1.
The Declaration Of Performance for these cables can be found under fibre cables and the corresponding cable for fibre count and fibre type in the section “Micro-Bundle Universal Bca”.
In addition the cables meet the requirements for flame non-propagation (IEC 60332-1) and fire non-propagation (IEC 60332-3).
MTP*-MTP Pre-Term characteristics
The MTP-MTP Pre-Term has standard pinned (male) connectors. This matches with the un-pinned (female) connectors in the ENSPACE modules and the female Plug&Play modules.
In order to reduce overlengths in data centers the Pre-Terms are custom made and available with 1m increments. The "xxx" in the N-number is the length in metre between the cable glands, i.e. the Pre-Term length between the back side of the patch panels.
After the cable gland the Pre-Term has a fan-out. The fan-out splits the cable into tubes. The tubes are reinforced with aramid yarns. At the end of each tube a MTP-connectors is mounted. The jacket of the tube is the same colour as the cable jacket. Close to the MTP-connector a label is installed to identify the number of the leg.
The Pre-Terms are optimized for both pulling and laying in data centers. On both sides the MTP connectors are protected by a bubble foam. On one side there is also a protecting net around the fan-out with MTP connectors and a pulling eye. The maximum pulling force on the pulling eye is 450N.
The MTP-MTP Pre-Terms come with a PG-13 cable gland that fits into the LANmark-OF ENSPACE and Plug&Play patch panel slots.
Optical Performance and Polarity
The typical value for the insertion loss for a low loss multimode and singlemode MTP-MTP* connection is 0,125 dB. The limit value is 0,3 dB measured according
to standard IEC61300-3-45.
The minimum return loss for a multimode MTP connection is 20 dB measured according to IEC 61300-3-6. The minimum return loss for a singlemode MTP connection is 45 dB measured according to IEC 61300-3-6.
The method C Pre-Term has a key up / key down design with a fibre pair-flip. This is in agreement with standard TIA 568-B-1-7-2006 method C.
For a duplex transmission like for 10GBase-SR (10G) polarity in the channel is maintained with this method C design and the use of the same straight cassettes on both sides. In addition the same patch cords can be used on both sides.
For parallel optics like for 40GBase-SR4 (40G) these method C Pre-Terms can be used with key up/key down adaptors on one side of the channel and key up/key up adaptors on the other side. The same straight female-female patch cords can be used on both sides.
|Caractéristiques de construction|
|Type de fibres optiques||OM5 50/125 Wideband|
|Nombre de fibres optiques||24|
|Diamètre externe nominal (mm)||5,9mm|
|Poids net approximatif||35kg/km|
|Caractéristiques de transmission|
|Insertion Loss, maximum, dB||0,3dB|
|Return Loss, Minimum, dB||20dB|
|Résistance mécanique aux chocs||10 impacts of 1 N.m|
|Résistance à l'écrasement (IEC 794-1-E3)||100N/cm|
|Température ambiante lors de l'installation, plage||0 .. 40°C|
|Température ambiante d'utilisation, plage||-10 .. 60°C|
|Température de stockage, plage||-20 .. 60°C|
|Rayon de courbure minimum en utilisation statique||90mm|
|Rayon de courbure minimum en utilisation dynamique||120,0mm|
|Non propagateur de la flamme||IEC 60332-1|
|Non propagateur de l incendie||IEC 60332-3|